The step-by-step system overhaul process at the Wellin Hall, inside the performance venue of Hamilton College in Clinton, NY.

The town of Clinton, NY is the home of Hamilton College. Precision Audio Services has provided audio engineering services to the college’s Music and Theater Department for several years, and this spring the company heads up a sound system upgrade in Wellin Hall. The 700-seat hall has served as the central hub of music education and concerts for the college since its construction in the 1980s. The bare concrete and polished wood walls combined with flown wooden acoustic panels above the audience creates a highly reverberant environment—perfect for the hall’s original purpose of unamplified acoustic performances.

However, these properties that make the environment desirable for acoustic performances, also make sound-reinforced events a significant challenge. "With an RT60 of almost 2.5 seconds, achieving a clear mix and vocal delivery is typically a major source of frustration for visiting mix engineers,” says Michael Lawrence from Precision Audio Services. “Although to a large extent, this is simply the reality of working in such an environment, one of the goals for the new design was to increase the consistency over the space and minimize excess energy splashing onto the walls and other non-audience surfaces, both areas where the current installed system struggled."

Another design challenge was presented by the way the space is used – or, more accurately, ways. The hall hosts a wide variety of musical, theatrical, dramatic, and speech events that necessitate a large degree of flexibility, where the current system presented some limitations. “We have three different mix positions depending on the needs of the show,” explains the venue’s Technical Coordinator, Bill Di Paolo. “Sometimes we are driving press feeds, live stream feeds, backstage zones, and we need a way to pull those feeds off the console without the operator having to jump through hoops. Another thing that’s been a bit of a problem for us is that the current mains are dead hung, so there’s no way to get to them for maintenance if there’s an issue. We had to swap out a bad box last year and it turned into a whole labor call just to get the box down to the deck to be worked on.”

The system design is far from the traditional install-patch approach. “Sometimes I have to adapt to things very quickly, on the fly, and in the past that’s been a challenge where we couldn’t get physical access to a loudspeaker, or all the signal flow was happening in the back of a rack somewhere with no easy way to get signals in or out of the rig at various points in the chain,” Di Paolo notes. “For larger events, we typically have a dedicated sound engineer but often it’s just me trying to handle multiple things at once, or we have a student operator, and so we need to be able to get to things easily.”

Starting from the console outputs, the new system design approach allows quick and easy changes before or after the processor, all the way to the loudspeaker positions themselves. No punch-down connectors in the back of racks – all the system patch points were brought to the front of the drive rack in a custom XLR patch bay system from Elite Core Audio, resembling more of a touring rack design mentality. I knew of several DSPs that would have been an appropriate fit for this project, but settled on an Allen & Heath AHM-64, which I felt offered the “best of both worlds” between a typical install-type free-wire DSP and a more live-oriented fixed-structure DSP.

An A&H IP6 controller sits next to the mixing console, configured for quick access to mute/unmute the entire PA plus dedicated mute and level controls for the ADA assistive listening system, the backstage 70-volt system, and the press send. These feeds are derived from the console mix and accessible via the patch bay, so providing a press send is as simple as plugging in a cable and turning a knob to adjust for the mic or line level requirement of the press equipment.

The main PA hangs presented some issues as well – the existing hang point locations didn’t allow for the hangs to be lowered for maintenance due to the proximity of the loudspeakers to the hall’s architectural elements and lighting fixtures. "We decided to move the hang points onstage about 18 inches, which would further the clearance away from the side walls to allow the arrays to be freely raised and lowered. It required the creation of new points via custom-length bridles between existing steel. This enabled the system to be lowered for maintenance or simply have the trim height adjusted for various events. The standard trim height was chosen to be the best compromise of sightlines and coverage, while the chain falls gave the option to lower and re-splay the arrays for theatrical events in this space – something not achievable in the past." Lawrence explains.

El Campeonato Mundial de Snowboard volvió a Valmalenco (Italia) en enero de 2021, esta vez a puerta cerrada debido a la situación sanitaria. La competición de Alpe Palù se celebró en una zona de 60 kilómetros de pendientes de esquí durante cuatro días de competiciones en la nieve tras nueve años de ausencia. La compañía Frate Professional fue la encargada de instalar los sistemas de sonido y los equipos de video, con un sistema inalámbrico compuesto por varias estaciones apiladas con line arrays HDL 26-A y subwoofers HDL 35-AS de RCF.

El sistema de sonido solicitado por el cliente debía garantizar el refuerzo de sonido en toda la zona de competición, incluidas las zonas de salida y meta, con una distancia de 800 metros en línea recta entre los puntos de difusión principales. Fabio Frate y su equipo idearon una solución estratégica: “Para evitar largas tiradas de cable y el cruce de cables en la pista, decidimos utilizar puentes inalámbricos Neutrik Xirium entre la sala técnica del remonte y la zona de meta, donde se encontraba la sala de control. Una línea balanceada instalada con anterioridad en el centro de telesillas también permitió hacer una conexión con cable hasta el punto de difusión de la zona de salida”.

El sistema de sonido se instaló de forma permanente a lo largo de la pendiente de snowboard durante 5 días, incluido un día de preinstalación. El sistema estuvo funcionando durante 8 horas al día y se dejó al aire libre (y bajo la nieve) todas las noches de la competición. Solo se usaron fundas para la lluvia para proteger el panel trasero de conexiones de cada unidad. “RCF nos garantizó que el sistema funcionaría sin problema alguno, pues todos los componentes son resistentes al agua y pueden funcionar perfectamente a temperaturas bajo cero. Y así fue. Aquí la temperatura por la noche puede alcanzar los -25 °C”. Además del sistema de sonido, Frate Professional también instaló una pantalla LED en el exterior con un tamaño de píxeles de 3,9 mm para la reproducción de video sincronizado con el audio.