• 250 W RMS power handling
  • 131 dB max SPL
  • 65 ÷ 20000 Hz frequency range
  • 100° x 10° coverage angles
  • Fully equipped with neodymium transducers
  • Horn Loaded symmetric design
  • Wooden reinforced polypropylene enclosure
  • Steel grille with clothing
  • 2 x SPEAKON connectors

HL 6 is two-way full range system, ideal when line array performance is needed, and a fast and easy set-up is a must. The concept of this speaker derives from the touring industry, bringing in a compact cabinet all the experience of RCF professional sound. HL 6 features state-of-the art RCF transducers, two powerful 6.0” woofers for a solid bass reproduction, plus a high powered 1.75” voice coil compression driver mounted on a precise 100° x 10° waveguide to deliver vocal clarity with high definition and incredible dynamic. Due to its symmetrical design the HL 6 produces constant coverage without break up or attenuation, maintaining intelligibility, definition, and signal strength over distance. HL 6 comes in a structurally wooden reinforced composite polypropylene enclosure, and it is equipped with two rear handles for portability.


Part number:

HL 6
EAN 8024530019068

Sub-bajos legendarios

The RCF HL 6 features RCF transducers with neodymium magnets. RCF’s experienced engineering teams have specially developed and matched each component. An entire set of protections preserve product life and reliability.
High frequencies
  • High-performance RCF ND840
  • 1.75-inch diaphragm neodymium compression driver
  • 900 Hz crossover point
Frecuencias graves
  • Two 6” neodymium woofers
  • Low frequencies handling down to 65 Hz
  • Water resistant fiber doped cone
  • Polycotton M-roll surround
  • Hypervented magnetic structure
Responsive Image
Responsive Image

Constant directivity waveguide

The custom-designed waveguide allows a precise coverage of 100° x 10°, while also delivering a completely linear high-frequency response. The constant directivity waveguide delivers consistent coverage from 900 Hz to the highest audible frequencies.
Responsive Image

Perfect for installation

The passive architecture makes the HL 6 one of the lightest line array modules on the market. Combined with flexible rigging options and a wide range of accessories, it's the ideal line array for installation both in corporate environments or music venues. HL 6 provides plenty of sound pressure and clarity that can replace antiquated, oversized sound systems with improved acoustic performance.

Advanced design

The integrated fittings are both easy to use and reconfigurable, allowing the system engineer to create J-shaped and spiral arrays starting at 1° angle.
The hardware is designed for easy and fast setup. Up to 16 HL 6 modules can be fastened on a single flybar.
The heavy-duty front grille is powder-coated. A special transparent-to-sound foam backing inside helps to further protect the transducers from dust and debris.
Responsive Image
Responsive Image

The hl 6’s perfect low-frequency companion

Perfect for keeping the floor clear and maximizing the efficiency and coherence of the array, the low-frequency companion designed for the HL 6 is the high-performance flyable single 15” HL 35-S. The integrated fittings are both easy to use and reconfigurable, allowing the system engineer to extend the HL 6 lower range with one or multiple HL 35-S modules. It can be used attached to the flybar, on the floor, or stacked with the HL 6 on top. HL 35-S provides sound pressure and clarity that can replace antiquated, oversized sound systems with improved acoustic performance.
Especificaciones acusticas
Respuesta en frecuencia (-10 dB):
65 Hz ÷ 20000 Hz
SPL máx. a 1 m:
131 dB
Ángulo de cobertura horizontal:
Ángulo de cobertura vertical:
Índice de directividad (Q):
Sección de potencia
Full Range
Impedancia nominal:
16 ohm
Manejo de potencia:
250 W
Manejo de potencia pico:
1000 W PEAK
Amplificador recomendado:
500 W
Dynamic Active Mosfet
Frecuencias de cruce:
900 Hz
Motor de compresión:
1 x 1.0'' neo, 1.75'' v.c
Altavoz de bajos:
2 x 6.0'' neo, 2.0'' v.c
Sección de entrada/Sección de salida
Conectores de entrada:
Conectores de salida:
Cumplimiento estándar
Safety agency:
CE compliant
Especificaciones físicas
Material del gabinete/de la caja:
PP Composite
Integrated array mechanics
2 on the rear panel
Black - RAL 9005
237 mm / 9.33 inches
470 mm / 18.5 inches
377 mm / 14.84 inches
11.8 kg / 26.01 lbs
Informaciones de envío
Altura de paquete:
260 mm / 10.24 inches
Anchura de paquete:
550 mm / 21.65 inches
Profundidad de paquete:
425 mm / 16.73 inches
Peso de paquete:
13.3 kg / 29.32 lbs